Measuring for Safety

 

Keep Operations Rolling and Employees Safer

The key to successfully installing fall protection safety equipment is accurate measurement of the center line. As simple as this may sound, it is where companies often get into trouble and end up with equipment that doesn’t fit the application requirements.

Three Steps to Get the Right Measurements

1. Establish the Center Line.


Your design standard can be anything it needs to be, but establishing the center line is critical. These measurements are the basis of the drawings we send back to you for sign-off.

When you measure, always begin from the center of the vehicle to the face of what you are mounting the access gangway on (see Figure 1). Ideally, you would position a vehicle in the loading area so that the measurement is spot on. If you are unable to position a vehicle in your facility due to the current restrictions, then you should measure where the truck(s) should line up, possibly marked by a stripe on the floor.

For railcars, it is a bit easier, as the tracks are stationary. Measure from the center of the rail to the center of mounting. If you have a long platform with several railcars, you will need to measure each access spot.

Figure 1. Measuring the Center Line.

Measuring the Center Line

2. Determine Platform Height.


While important, platform height is not as critical as the center line measurement. Measure platform height from the bottom of the vehicle wheels to the top of where your worker will be standing and loading/unloading.

Not too long ago, OSHA changed the platform height standard. Truck platforms are now generally in the 10-12 feet range and hopper cars are 14-15 feet. Ramps are self-leveling, so if your measurements are off by a few inches, the ramp will compensate for it.

3. Identify Obstructions.


Obstructions are one of the trickiest things to get a handle on. When our team does a site visit, they can easily identify all of the potential obstructions—overhead walkways, piping, floor drains, etc.—that can complicate installation.

Sometimes, due to scheduling conflicts or worksite issues, site visits are not possible. The next best thing is to have you send us photos or to do a virtual walkthrough with us. Once we have seen your facility and the area where the safety equipment will be installed, we can guide you through next steps in making sure all obstructions are identified.

We’re Here to Help

Sam Carbis Solutions Group is here to help. Our team is available to guide you through any installation challenges or to answer any questions about how to keep your workers safer. In addition to installation, we can help with maintenance questions as well, and are available via phone, email, or a virtual visit to help you maintain your safety equipment.

Location: Florence, SC, USA

Popular posts from this blog

Does Hydraulic Fracturing Poison America's Groundwater?

You might be surprised to know that America actually has large oil reserves trapped deep underground in non-porous shale rock. Until horizontal drilling and fracking came along these reserves could not be breached. The average fracking mixture is 99.5% water and sand. As you can probably imagine, water is used in copious amounts –from 65,000 gallons to 600,000 gallons. This may sound like a lot of water, but not when put into perspective. The amount of water used in fracking is smaller than the amount used in agriculture, manufacturing and municipal water supplies. In the process of hydraulic fracturing, different chemicals can be used for different functions. Some chemicals limit the growth of bacteria, while others are used to prevent corrosion. Other chemicals are added to make fracking more efficient and effective. A typical fracture treatment uses low concentrations of anywhere from three to twelve additive chemicals. The initial drilling is a vertical wellbore that extends f
Read more

Tips For Transloading Crude Oil From Tanker Trucks To Rail Cars

Image
Transloading is the term used for the process that takes place when a shipment must be transferred from one mode of transportation to another. Transloading is often used in the oil industry because the pipelines to the refineries are in the south so if the well head is somewhere else in the country, the oil has to travel there. Transloading takes place when one type of transportation can’t make the entire journey or it may be more cost effective to transfer the shipment from one mode to another. Usually product (in this scenario it’s crude oil) is transloaded from tank trucks into about 120 connected railcars. Using railcars to carry product may sound old fashioned but it’s still the most consistently effective way to transport lots of products including crude oil. A tank truck terminal transloading to railcars will have a rail spur off the main train track. This way, the railcars can pull in and be loaded. Once loading is complete the cars continue back to the main railway for the jo
Read more

Three Crucial Tips For Preventing Accidents on Rail Hopper Cars

Image
Providing a safer work site for your employees is essential to reducing the risk of accidents, increasing throughput and maximizing your business’s bottom line. Failing to take proper rail safety precautions may lead to serious consequences including deaths, injuries, OSHA fines and other legal ramifications. Rail hopper cars are used to transport dry bulk commodities, such as flour, sand, plastic pellets, sugar and grains. The hatches on top come in a variety of configurations, leading to spotting challenges that make it difficult to protect your workers. Additionally, chutes and other loading equipment may create obstacles that prevent safe access. Many injuries and fatalities  have occurred after workers fell from the top of rail hopper cars. Adequate fall prevention strategies may have prevented many of these accidents. Here are three tips for preventing accidents on rail hopper cars: 1. Install Rail Safety Solutions Installing rail safety solutions is an important step in reduci
Read more